This coupler sits between the Bowden tube and nozzle block on an Ultimaker 2+/Extended+/2+ Connect. First introduced with the Ultimaker 2+ series printers, this part is also compatible with the Ultimaker 2, 2 Go, and Extended, and offers extended service compared...
Glass print bed approximately 9" x 10". Official Ultimaker spare part compatible with the following printers: Ultimaker 2+ Connect Ultimaker S3 Ultimaker 3 Ultimaker 3 Extended Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 2 Ultimaker 2 Extended Ultimaker Original+ Ultimaker Original with Official...
These are the short belts that connect the X and Y motors to the axes. Official Ultimaker Spare Parts for the following printers: Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 3 Ultimaker 3 Extended Ultimaker 2 Go Ultimaker 2 Ultimaker 2 Extended Ultimaker S5...
Official Ultimaker Spare Parts for Ultimaker² series printers; the 5VDC 0.08A rear fan on Ultimaker 2 Series printers that cools the printhead. Official Ultimaker spare part compatible with the following printers: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker...
OEM heated bed panel and cable for the Ultimaker 2+ Connect. The bed and cable set is compatible with the following machines: Ultimaker 2 Ultimaker 2 Extended Ultimaker 2+ Ultimaker2 Extended+ Ultimaker Original+ (and the Ultimaker Original with Official Heated Bed Upgrade...
One nozzle for all materials. The ruby tip provides exceptional wear resistance for printing with abrasive materials such as metal- or carbon-fiber-filled filaments, or glow-in-the-dark plastics, while retaining the exceptional thermal characteristics of a primarily brass nozzle. It also prints...
Official Ultimaker Spare Parts for the Ultimaker 3, Ultimaker 3 Extended, and Ultimaker 2+ Connect. This is a complete set of 4 sliding blocks and long S2M belts.
Not compatible with other models or series of Ultimaker printers.
Installation instructions available here.
Model Cooling Fan 12VDC (x2) (UM2/Go/Ext/UM2+/Connect)
$33.40
Official Ultimaker Spare Parts for Ultimaker² series printers; a pair of 12V DC 0.1A fans, as used for the side fans on all Ultimaker 2/Ultimaker 2+ series printers. Official Ultimaker spare part compatible with the following printers: Ultimaker 2+ Connect Ultimaker...
Official Ultimaker Spare Part: the Isolator Nut that connects the heater block to the TFM coupler and Bowden Tube. Compatible with the following Ultimaker printers: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 2 Go Ultimaker 2 Ultimaker 2...
A pair of strong Bowden tube collets and blue retaining clips compatible with all Ultimaker series of machines. These collets have thick teeth to provide additional grip on the bowden tube for the most reliable printing experience. When installed in...
This nozzle fits the Olsson block set (which is standard on the Ultimaker 2+ and Extended+). This nozzle is also compatible with the Ultimaker 2+ Connect.
The larger 0.6mm opening size allows for faster volumetric print speeds than the standard 0.4mm nozzle.
Power Adapter 24v-220w and Cable (UM3/UM2/UMO+/Connect)
$195.60
Official Ultimaker 24V Power Supply for the Ultimaker 2 series, Ultimaker Original+, and Ultimaker 3 series printers. Includes cable for standard US-style 3-pin wall socket. Compatible with the following machines: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2+ Extended Ultimaker 2 Ultimaker 2...
Light machine oil like sewing machine oil should be applied regularly to all of the smooth axis rods on your printer to keep everything in smooth operation. Compatible on the following printer models: Ultimaker S7 Ultimaker 2+ Connect Ultimaker 2+ Ultimaker...
This nozzle fits the Olsson block set, and provides a more wear-resistant tip that is better suited to printing with abrasive materials like Stainless Steel, or Carbon Fiber filaments. *Note: the opening in these nozzles is 0.5mm - some earlier...
Thick green machine grease used for lubricating the trapezoidal lead screw on your printer and ensuring smooth movements on the Z-axis. Compatible on the following printer models: UltiMaker S7 Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 3 Ultimaker...
This nozzle fits the Olsson block set (which is standard on the Ultimaker 2+ and Extended+). This nozzle is also compatible with the Ultimaker 2+ Connect.
The larger 0.8mm opening size allows for faster volumetric print speeds than the standard 0.4mm nozzle.
A pair of the spring clips for holding the glass in place. These clips can be used on all 4 corners of the bed, or on the back two corners as preferred. These are official Ultimaker spare parts, compatible with the following...
Print Head Linear Bearing Pack (UM2/Go/Ext//ConnectOriginal/UMO+)
$36.50
Official Ultimaker Spare Parts for all Ultimaker Original and Ultimaker 2 family printers: Ultimaker 2 Ultimaker 2+ Ultimaker 2 Extended Ultimaker 2 Extended+ Ultimaker 2+ Connect Ultimaker 2 Go Ultimaker Original Ultimaker Original+ This is a pack of two LM6LUU linear...
This nozzle fits the Olsson block set (which is standard on the Ultimaker 2+ and Extended+). This nozzle is also compatible with the Ultimaker 2+ Connect. The smaller 0.25mm opening size allows for finer detail in the X/Y plane, compared to the standard 0.4mm nozzle, however,...
Safety glass clips, one each for the left and right front corners of the bed plate. Official Ultimaker spare part, can be used with the following Ultimaker printers: Ultimaker S5 Ultimaker S3 Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+...
This 9.4mm spacer sits between hot end holder top and TFM coupler on the UM2+/UM2X+ printhead. It can replace the printhead spring on the UM2Go/UM2/UM2X. Official Ultimaker spare part, compatible with the following printers: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker...
Filter assembly from Ultimaker for the Ultimaker S7, Ultimaker S5, and Ultimaker 2+ Connect Air Managers. Filters should be replaced after approximately 1500 hours of runtime.
The 8mm single pulley, assembled with a set screw, is used on all Ultimaker 2 series, Ultimaker 3 series, and Ultimaker S-Line printers. This is an official Ultimaker part for the following machines: Ultimaker 2+ Connect Ultimaker S3 Ultimaker S5...
Official Ultimaker Spare Parts for UM2 series printers. Compatible with the following printers:
Ultimaker 2+ Connect
Ultimaker 2
Ultimaker 2+
Ultimaker 2 Extended
Ultimaker 2 Extended+
Ultimaker 2 Go
The 5mm pulley, assembled with a set screw, is used on all Ultimaker 2 series, Ultimaker 3 series, and Ultimaker S-Line printers. This is an official Ultimaker part for the following machines: UltiMaker S7 UltiMaker S5 Ultimaker S3 Ultimaker S5...
Official Ultimaker Spare Parts for UM2 series printers. Compatible with the following printers:
Ultimaker 2+ Connect
Ultimaker 2
Ultimaker 2+
Ultimaker 2 Extended
Ultimaker 2 Extended+
Ultimaker 2 Go
The 8mm double pulley, assembled with a set screw, is used on all Ultimaker 2 series and Ultimaker 3 series printers. This is an official Ultimaker part for the following machines: Ultimaker 2+ Connect Ultimaker 3 Ultimaker 3 Extended Ultimaker 2+ Ultimaker...
Official Ultimaker UMB (Ultibus) cable for the Ultimaker S7 and Ultimaker S5 Air Manager. Also compatible with the Ultimaker 2+ Connect. This part is most often needed for resolving ER80 error messages.
This nozzle fits the Olsson block set (which is standard on the Ultimaker 2+ and Extended+) and is a direct replacement for the standard 0.4 nozzle tip. Compatible with the: Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 2+ Connect Ultimaker 2 with Extrusion...
Official Ultimaker Spare Parts for UM2 series printers. Compatible with the following printers:
Ultimaker 2+ Connect
Ultimaker 2
Ultimaker 2+
Ultimaker 2 Extended
Ultimaker 2 Extended+
Ultimaker 2 Go
The DR2160 spring is an official Ultimaker spare part used in several places across multiple machines. It is used in the: Ultimaker 2+ feeder Ultimaker 2 Extended+ feeder Ultimaker 3 feeder & heated bed Ultimaker 3 Extended feeder & heated...
This nozzle fits the Olsson block set (which is standard on the Ultimaker 2+ and Extended+). The very small 0.15mm opening size allows for very fine detail in the X/Y plane, compared to the standard 0.4mm nozzle. Note: This nozzle is for expert users only; it...
This is the official printhead for the Ultimaker 2+ Connect.
This can be installed on the following machines:
Ultimaker 2+ Connect
Ultimaker 2+
Ultimaker 2 with the Extrusion Upgrade Kit
NOT compatible with:
Ultimaker 2 Extended
Ultimaker 2 Extended+
This nozzle fits the Olsson block set (which is standard on the Ultimaker 2+ and Extended+). The larger 2mm opening size allows for extremely high volumetric print speeds compared to the standard 0.4mm nozzle, albeit with a greater risk of oozing, and a loss of...
The Power Cable US Type C13 is an official Ultimaker Spare Part. This power cable is compatible with the following models of Ultimaker printers: Ultimaker S7 Ultimaker S5 Ultimaker S3 Ultimaker 3 Ultimaker 3 Extended Ultimaker 2 Extended+ Ultimaker 2+...
Limit switch for the X direction with 940 mm white cable and a blue shrink sleeve. UltiMaker spare part compatible with:
UltiMaker S3
UltiMaker S5
UltiMaker S7
UltiMaker 2+ Connect
Not compatible with Ultimaker 3 series or Ultimaker 2 series machines.
Pack of 5 black plastic clips to secure the braided bowden tube to the braided cable.
Official Ultimaker Spare Part for.
Ultimaker 2
Ultimaker 2Go
Ultimaker 2 Extended
Ultimaker 2+
Ultimaker 2 Extended+
Also compatible with the Ultimaker 2+ Connect.
10mm pulley spacer for the XY gantry. OEM UltiMaker part for the following printers:
UltiMaker S5 R1
UltiMaker 2+ Connect
UltiMaker 2+
UltiMaker 2 Extended+
UltiMaker 2
UltiMaker 2 Extended
UltiMaker 2 Go