parts
SA006-N AMS Lite Filament Hub
$5.99
The AMS lite Filament Hub is a key part of reliable filament switching during multi-color or multi-filament printing. One end of the hub connects to 4 different PTFE tubes (up to 4 filaments), while the other end connects to the top of...
View full product details
SA011 - Filament Buffer (P2S)
Sold Out
The filament buffer is a special component installed on the back of the printer to reduce tension fluctuations during the feeding process and ensure smooth filament feeding. What's in the box? 1x Filament buffer 2x ST3x24x7 screws
View full product details
SA013 - AMS Hub (A1/A1 Mini)
Sold Out
This HUB accessory is specifically designed for A1-series 3D printers, serving as a standardized hub for seamless connectivity and integrated functionality between the AMS, AMS 2 Pro, and AMS HT. What's in the box? -AMS HUB x1-4 Pin Cable x1-PTFE...
View full product details
SAA029 - Desiccant x6 (AMS 2 Pro/AMS HT/AMS)
$3.99
This is a 6 pack of reusable Desiccant pouches for the AMS 2 Pro and AMS HT to keep your filaments dry. This Desiccant can also be used on the AMS. The color-changing silicone desiccant absorbs moisture. After the desiccant...
View full product details
Safety Glass Clips (UM2/UM3/UMO+/S3/S5/Connect)
$27.70
Safety glass clips, one each for the left and right front corners of the bed plate. Official Ultimaker spare part, can be used with the following Ultimaker printers: Ultimaker S5 Ultimaker S3 Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+...
View full product details
Single Pulley Assembly (Gear Ratio) UMS5/S3
$25.40
The single pulley assembly (Gear Ratio), assembled with a set screw, is used on the Ultimaker S-Line printers. This is an official Ultimaker part for the following machines: Ultimaker S3 Ultimaker S5 Ultimaker S7
View full product details
Sliding Block Set (S3)
Sold Out
This is a set of fully assembled sliding blocks on Ultimaker S3 belts. This part is compatible only with the Ultimaker S3. Installation instructions are available here.  Â
View full product details
Steel Nozzle - 0.5mm
$13.00
This nozzle fits the Olsson block set, and provides a more wear-resistant tip that is better suited to printing with abrasive materials like Stainless Steel, or Carbon Fiber filaments. *Note: the opening in these nozzles is 0.5mm - some earlier...
View full product details
Switching Adapter for AMS 2 Pro
$32.99
If you need to dry the filaments in more than one AMS 2 Pro at the same time, you will need to use the Bambu Lab official Switching Adapter to power the additional AMS 2 Pro.If the X1, P1, A1...
View full product details
The Olsson Ruby Nozzle
$45.00 $90.00
One nozzle for all materials. The ruby tip provides exceptional wear resistance for printing with abrasive materials such as metal- or carbon-fiber-filled filaments, or glow-in-the-dark plastics, while retaining the exceptional thermal characteristics of a primarily brass nozzle. It also prints...
View full product details
Thermocouple Sensor
$46.40
Thermocouple printhead temperature sensor for the Ultimaker Original only. Not compatible with the Ultimaker 2 series, nor with the Ultimaker Original+. Official Ultimaker Spare Part.
View full product details
Thermocouple Transmitter Board (UMO)
$34.00
The amplifier board that sits on the printhead of the Ultimaker Original, and interfaces the thermocouple to the main electronics board. Not compatible with Ultimaker Original+ or Ultimaker 2 printers.
View full product details
UltiController Kit (UMO)
$116.25
Kit of parts needed to add a control interface and USB card reader to an Ultimaker Original, or repair/replace the Ulticontroller on an Ultimaker Original+. Avoids the need to keep the printer tethered to a computer during printing. Requires a...
View full product details
Ultimaker 2 Isolator Spacer 9.4mm (UM2+/UM2X+/Connect)
$9.99
This 9.4mm spacer sits between hot end holder top and TFM coupler on the UM2+/UM2X+ printhead. It can replace the printhead spring on the UM2Go/UM2/UM2X. Official Ultimaker spare part, compatible with the following printers: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker...
View full product details
Ultimaker 2+ Maintenance Kit (MK)
$225.00 $435.00
Over $150 in savings if you purchase the Ultimaker 2+ Maintenance Kit instead of buying the parts separately. Save now! Our comprehensive Maintenance Kit contains everything you need to maintain your Ultimaker 2+ and Ultimaker 2 Extended+ with ease and...
View full product details
Ultimaker BB Print Core (0.8mm) (UM3/S5/S3/S7/Factor4)
$169.00
A genuine 'BB' style Ultimaker Print Core with a 0.8mm nozzle, for printing PVA support material. Compatible with the following Ultimaker printers: Ultimaker 3 Ultimaker 3 Extended Ultimaker S3 Ultimaker S5 Ultimaker S7 UltiMaker Factor 4 Â
View full product details
Ultimaker Print Core CC .4mm (S3/S5/S7/Factor4)
Sold Out
Ultimaker’s CC 0.4 mm Print Core enables you to print using abrasive materials on your S-series or UltiMaker Factor 4 3D printer. This new print core contains a highly wear-resistant hardened steel nozzle and titanium heat break, making them more...
View full product details
Ultimaker Print Core CC .6mm (S3/S5/S7/Factor4)
$299.00
 Ultimaker’s CC 0.6 mm Print Core enables you to print using abrasive materials on your Ultimaker S-Series or Factor 4 3D printer. This new print core contains a highly wear-resistant hardened steel nozzle and titanium heat break, making them...
View full product details
Ultimaker Print Core HT .6mm (Factor 4)
$349.00
Ultimaker’s HT 0.6 mm Print Core enables you to high temperature materials on your UltiMaker Factor 4 up to 340C, including UltiMaker PPS CF. This product is officially supported for the UltiMaker Factor 4 printer only.
View full product details
XY Motor Assembly (S7/S5/S3/UM2C)
$45.10
XY Motor assembly for Ultimaker S7, Ultimaker S5, Ultimaker S3, and Ultimaker 2+ Connect printers. Official Ultimaker spare part.
View full product details