Official Ultimaker Spare Parts for the Ultimaker Original and Original+. Complete set of 4 long and 2 short MXL belts.
Not compatible with Ultimaker 2.
Official Ultimaker Spare Parts - compatible with the Ultimaker 2+/2Ext+, Ultimaker 2 (inc Go and Extended variants), and the Ultimaker Original+. Includes the main electronics board and safety jumpers. Not compatible with the Ultimaker Original. Please note: the current version of...
X-Axis end stop switch (Blue wire).
Official Ultimaker spare part compatible with the following printers:
Ultimaker 3
Ultimaker 3 Extended
Ultimaker 2
Ultimaker 2+
Ultimaker 2 Extended
Ultimaker 2 Extended+
Note:Â NOTÂ compatible with the UMO/UMO+, S5, S3, or Ultimaker 2+ Connect.
Official Ultimaker Spare Parts for the Ultimaker Original (includes the Arduino Mega and four stepper driver cards).
Not compatible with Ultimaker 2 series, or Ultimaker Original+.
A pair of the spring clips for holding the glass in place. These clips can be used on all 4 corners of the bed, or on the back two corners as preferred. These are official Ultimaker spare parts, compatible with the following...
This is the cable that runs between the main electronics and the heated bed panel on the Ultimaker 2+, Ultimaker 2 Extended+, and Ultimaker Original+. This is an updated version of the cable, released in 2016. If your heated bed...
Official Ultimaker spare part for the Original and Original+. Not compatible with Ultimaker 2.
Aluminum heater block accepts M6 threaded nozzle and isolator tube, as well as heater cartridge and temperature sensor.
Â
Official Ultimaker Spare Parts for Ultimaker 2+ and Extended+ printers. This heater cartridge is 24V, 35W.
Â
Note: This is not compatible with the (non-Plus) Ultimaker 2, Ultimaker 2 Extended, Ultimaker Original/+, Ultimaker 2Go or Ultimaker 2+ Connect printers.
Official Ultimaker Spare Part: the Isolator Nut that connects the nozzle/block to the PTFE coupler and Bowden Tube. Compatible with the following Ultimaker printers: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 2 Go Ultimaker 2 Ultimaker 2 Extended...
Official Ultimaker Spare Parts for Ultimaker² series printers; the 5VDC 0.08A rear fan on Ultimaker 2 Series printers that cools the printhead. Official Ultimaker spare part compatible with the following printers: Ultimaker 2+ Connect Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker...
Hot end parts pack comprising the heater block, nozzle and brass tube, plus teflon isolator, PEEK insulator. Also includes the Bowden tube retaining collet and blue clip.
Official Ultimaker spares for the Ultimaker Original and Original+.
Official Ultimaker spare parts for the Ultimaker Original and Original+. This kit includes all of the injection molded parts in this photo, including those for the feeder assembly.
Model Cooling Fan 12VDC (x2) (UM2/Go/Ext/UM2+/Connect)
$23.40
Official Ultimaker Spare Parts for Ultimaker² series printers; a pair of 12V DC 0.1A fans, as used for the side fans on all Ultimaker 2/Ultimaker 2+ series printers. Official Ultimaker spare part compatible with the following printers: Ultimaker 2+ Connect Ultimaker...
Official Ultimaker Spare Parts for Ultimaker Original and Original+; PEEK isolator connects the PTFE coupler at the end of the Bowden Tube to the brass tube and heater block.
This is the print head assembly for the Ultimaker 3 and Ultimaker 3 Extended. It includes all pictured parts here, including the printhead cable, fans, and nozzle seal. If you're looking for spare nozzle seals for this printhead, they are...
Set of 3 separate injection-moulded parts that comprise the print head block for Ultimaker 2 Series printers.Â
Official Ultimaker spare part compatible with the following printers:
Ultimaker 2+
Ultimaker 2 Extended+
Ultimaker 2 Go
Ultimaker 2
Ultimaker 2 Extended
The DiBond panel that folds over the z-stage bearing at the back of the print bed. Compatible with Ultimaker 2, and Ultimaker 2 Extended.
Official Ultimaker Spare Parts.
Printhead Temperature Sensor (PT100B 'Glassfiber' for UM2+/Extended+)
$52.80
This is the official Ultimaker spare part for the Ultimaker 2+ and Ultimaker 2 Extended+ printers.
Â
Note: This is not compatible with the (non-Plus) Ultimaker 2, Ultimaker 2 Extended, Ultimaker Original/+, Ultimaker 2Go or Ultimaker 2+ Connect printers.
Printhead Temperature Sensor (PT100B) UM2/UM2X/UM2Go/UMO+
$45.00
This is the official Ultimaker spare part for the Ultimaker Original+.
Also compatible with the Ultimaker 2, Ultimaker 2Go, and Ultimaker 2 Extended.
Not compatible with the Ultimaker 2+ or Ultimaker 2+ Extended.
Official Ultimaker Spare Parts for the Ultimaker 2 series printers. This is a complete set of 4 sliding blocks and long belts. Compatible with the following models of Ultimaker printer: Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 2 Ultimaker 2 Extended Not...
Official Ultimaker Spare Parts for the Ultimaker 3, Ultimaker 3 Extended, and Ultimaker 2+ Connect. This is a complete set of 4 sliding blocks and long S2M belts.
Not compatible with other models or series of Ultimaker printers.
Installation instructions available here.Â
This coupler sits between the Bowden tube and nozzle block on an Ultimaker 2+/Extended+/2+ Connect. First introduced with the Ultimaker 2+ series printers, this part is also compatible with the Ultimaker 2, 2 Go, and Extended, and offers extended service compared...
These are the short belts that connect the x and y motors to the axes. Official Ultimaker Spare Parts for the following printers: Ultimaker 2+ Ultimaker 2 Extended+ Ultimaker 3 Ultimaker 3 Extended Ultimaker 2 Go Ultimaker 2 Ultimaker 2 Extended...